Unroller on the bottom for 300kg, with brake, bearing on sides, self-aligning, on the bottom.
Unroller on top of a multiple table for 300kg, with brake, bearing on sides, self-aligning, on top.
Decoiler for 5000kg, with brake, bearing on sides, manual expansion, stationary, movable or stackable.
Decoiler for 2000kg, with brake, bearing on one side, manual expansion, stationary or stackable.
Decoiler for 2000kg, powered, bearing on one side, manual expansion, stationary or stackable.
Decoiler for 3000kg, powered, bearing on one side , hydraulic expansion
Decoiler for 5000kg, powered, bearing on one side, hydraulic expansion, stationary.
Decoiler for 7000kg, powered, bearing on one side, hydraulic expansion, stationary.
Decoiler for 12000kg, powered, bearing on one side, hydraulic expansion, stationary.
Only with a pressure roll can thicker sheets be safely loaded, opened and stretched into the machine by one operator.
If you work with stainless steel coils with protective paper, we recommend using the electric paper recoiler, which can be mounted on the machine frame of any powered decoiler.
If your line has a single decoiler, the scissor coil car is electrically moveable and can be raised and lowered hydraulically.
Only with a roller table can thicker sheets be safely fed into the subsequent machine by one operator.
If a multi table is fed from braked decoilers the sheets are decoiled via bearing equipped rollers in the deflection roller stand.
If a multi table is fed from powered decoilers the sheets are supported by the guideways when advanced and reversed.
If a multi table is fed from powered decoilers the sheets are supported by the guideways when advanced and reversed.
If a multi table is fed from powered decoilers the sheets are supported by the guideways when advanced and reversed.
The coil guide is an important component for the functionality and accuracy of every line.
The coil guide is an important component for the functionality and accuracy of every line.
The coil selector is a very economical solution to implement a rapid and easy change of sheet.
With the powered coil selector you ensure flexible access to all of the various coils you need every day - because a sheet change occurs automatically in no time.
With the powered coil selector you ensure flexible access to all of the various coils you need every day because a sheet change-over occurs automatically in no time.
The film applicator can be installed on basically any table.
Sheet thicknesses up to 1.00 mm can be straightened with the 6-roller straightener.
With the 6-roller straightener you can create mark-free, flat sheets.
With the 6-roller straightener you can create mark-free, flat sheets.
The MST multiple slitter allows rapid fabrication of individual blanks from coils. A precisely cut blank from the particular sheet required reduces waste to a minimum and measurably increases productivity.
The MST multiple slitter allows rapid fabrication of individual blanks from coils. A precisely cut blank from the particular sheet required reduces waste to a minimum and measurably increases productivity.
With the programmable slitting unit PSM you can enter your desired strip widths at the touch panel.
The trim stripe recoiler recoils edge stripes of coils onto a mandrel, saving space.
The proven roller shear guarantees precise and burr-free blanks, low space requirements and favourable investment costs.
The programmable crosscut shear has a flat knife at the bottom and a roller knife at the top. The circular blade can therefore cut strip sheets from both sides and does not require an idle stroke.
The guillotine shear can be described as the "classic" among the cross-cutting shears. Fast, precise and burr-free cuts are its trademark.
To facilitate access to the knife adjustment, a folding table can be installed between the strip shear and the guillotine shear for entry into the machine.
The outfeed roller is designed as a conveyor belt running synchronously with the machine with an ejection roller to support blanks during the cutting stroke and to convey them out of the guillotine shear. This considerably increases cutting quality and safety.
With the recoiler, slit or wide strips can be easily wound into small coils. The coils are wound relatively loosely to a small diameter of 300 mm and an optically clean coil is produced after binding and setting up.
With the recoiler, slit or wide strips can be easily wound up. The coils are wound tautly to a diameter of 508 mm and an optically clean coil is produced after binding and removal.
With the recoiler, slit or wide strips can be easily wound up. The coils are wound tautly to a diameter of 508 mm and an optically clean coil is produced after binding and removal.
The cut-to-length shear is an efficient option for any coiler when a heavy starting coil is being wound into several pieces. There is no need to set up the machine again.
The belt ejector is motorized with belt, strap or rollers and is used for
sheet metal-friendly conveying of individual sheets for subsequent processing.
The stacking table is designed as a hydraulically operated scissor lift and lowers automatically as the stack of sheets increases.